Install the tile mural using conventional tile adhesives and tools. Care must be taken not to scratch the face of the tiles with hard objects, such as other tiles or metal tools. Normal use of tile backerboard and leveling materials are required as with conventional tile, particularly where moisture or possible leakage could occur.
(NOTE: Tumbled Marble Tile is more porous than other tile types. Prior to installation, it should be sealed with a clear tile sealer, especially if the tumbled marble mural will be exposed to moisture during use. Sealing prior to installation will also aid in grout cleanup. Recommendations: Custom Building Products' TileLab SurfaceGard Penetrating Sealer (#TLSGSPT) and Aqua Mix's 'Sealer's Choice Gold.')
Tiles for large murals are numbered on the back and marked for layout, from left to right and top to bottom. Small murals may simply be laid out and transferred to the wall for attachment.
Use denatured alcohol, mineral spirits or glass cleaner for clean up. Do not use extremely strong chemicals such as muriatic acid, acetone, gasoline, or lacquer thinner.
Custom tiles may be used in any interior commercial and residential environment (see our Exterior Grade tiles for extended sun exposure). Installations subject to moisture or temperature fluctuations should be grouted to prevent seepage around the tiles or cracking due to substrate movement.
(For countertops and bar tops, we recommend our Porcelain imaged tile and Glass Tiles. Apply a sealer over the grout to avoid stains in the grout. You may also apply special topcoats (e. g., catalyzed epoxy) after installation for increased hardness, depth-of-image, and scratch protection. Porcelain Tile and Glass Tiles are also recommended for exterior use in shaded or covered areas as direct, long-term exposure to the sun will eventually cause fading in the image.)
Grouting:
Wall tiles: Use silicone grout or non‑abrasive (unsanded) tile grout. Set your tiles with adhesive and grout them in after the period of time recommended by the adhesive manufacturer. (Recommendations: LATICRETES 1600 Series Tri‑Poly Fortified Unsanded Grout by LATICRETE International, Inc., Bethany CT 06524‑3423 USA, (800) 243‑4788 ext. 235, www.LATICRETE.com. For exterior use, mix with LATICRETE 1776 Grout Admix Plus in place of water to provide a dense, colorfast grout joint that inhibits stain causing bacteria, mold and mildew growth; also suitable for interior.) Only porcelain or glass tiles should be considered for exterior use in climates subject to frost. Avoid prolonged direct sunlight exposure.
Ceramic and Porcelain floor tiles: For interior use only. Use sanded or unsanded grout. Be careful with tools to avoid excessive abrasion and scratching. Observe all usual precautions for preparation as with conventional floor tiles (leveling, stability, cleanliness). For unshaded outdoor use, see Exterior Grade tiles.
As with any tile, DPI custom imaged tiles should be cleaned using a non-abrasive cleaner, such as Scrubbing Bubbles, Lysol Tub & Tile, Fantastik, glass cleaner or denatured alcohol with a non-abrasive sponge or cloth. The tiles are resistant to dilute bleach. Do not use extremely aggressive chemicals such as muriatic acid or acetone. Our Glass Tiles are resistant to all chemicals and cleansers.
Q: What if I break a tile during installation?
A: Dependable Printing & Imaging can supply replacement tile. For this
purpose, we keep a digital file of every mural produced for at least one
month. Shipping on replacement tiles is not included.
Q: Can these murals be installed outside?
A: Imaged tiles should not receive prolonged direct sunlight but can be
placed under awnings and on north-side exposures. Our
Porcelain Tiles and
Glass Tiles are perfect for climates that experience freezing
temperatures. Periodic or intermittent sun exposure will not damage the
image. For extended sunlight exposure, we have
Exterior Grade tiles.
Planning A Mural | Durability Tests | Tile Mural Order | Floor Tile Order | Art Gallery | Installation/Cleaning | Resources-Links
Site Map Frequently Asked Questions Sending Images/Mural Size Terms and Conditions
 |
General Help & Production
Email - Mitch Bernard
434-660-7170
Clerical - Debbie Bernard
Shipping/Receiving - Barrett
Johnson
Fax 434-369-7179
Dependable Printing & Imaging 1701 Avondale Drive Altavista,
VA 24517-1009
Member Altavista Area Chamber
of Commerce
All rights to content and format on entire web site reserved to Dependable Printing
& Imaging
©Dependable Printing & Imaging
We use a 'first-party' cookie to aid our
website analytics. We do not obtain personal information or plant adware or
malware on your computer.